 Junior Member Thread Starter Join Date: Aug 2011 Posts: 1 Had my 2008 Sonata scanned for a check engine light. Came up with code 016 = Cam and/or Crankshaft sensor. Had no trouble identifying the cam sensor, but cannot find the crank sensor. Repair manual has no picture, or figure in anywhere as to the location; states that it's located on drivers side at the back of the engine near the flywheel. Join Date: Aug 2011 Location: Elkhart Lake, WI Posts: 3 I have an '04 Sonata but can't imagine the locations are too different, the crank sensor is at the crankshaft sprocket, you may have to remove the timing belt and drive belt to see it. Last edited by NovaResource; 08-22-2011 at 12:34 PM. Reason: Removed spammed link Join Date: Jan 2008 Location: USA-Montana Posts: 1,288 The 2.4 liter used in the 2008 Sonata is a totally different engine design than the motor used in the 2004 model. The crankshaft position sensor is mounted on top of the bell housing where it buts up against the engine block. See attachments. Join Date: Mar 2010 Posts: 900 Quote: Originally Posted by ken99 The 2.4 liter used in the 2008 Sonata is a totally different engine design than the motor used in the 2004 model. The crankshaft position sensor is mounted on top of the bell housing where it buts up against the engine block. See attachments. HEHEHEHEEEE,,,, NO IT AINT ....... It is bulkhead side of engine, in corner where ear is for trans mounting just above the oil pan rail.. got to do it from underneath, after taking a couple shields off.. what a piece of work.. Crank position will toss a 0335 code.. you Likely run into a OCV for CVVT.. Join Date: Jan 2008 Location: USA-Montana Posts: 1,288 Quote: Originally Posted by sbr711 HEHEHEHEEEE,,,, NO IT AINT ....... LOL...Yeah, you caught me iting the schematics without double checking under the hood of our 2009. I knew better too. Join Date: Feb 2015 Posts: 1 Quote: Originally Posted by sbr711 HEHEHEHEEEE,,,, NO IT AINT ....... It is bulkhead side of engine, in corner where ear is for trans mounting just above the oil pan rail.. got to do it from underneath, after taking a couple shields off.. what a piece of work.. Crank position will toss a 0335 code.. you Likely run into a OCV for CVVT.. SBR711 can you send a picture of where the crankshaft position sensor is located i have been searching for a week? Join Date: Feb 2019 Posts: 1 If you still need the location of the cps, I just replaced mine. 2009 Sonata 2.4L, Good luck!
Thread Thread Starter Forum Last Post Accent09GLS Hyundai Accent 0 07-04-2015 12:15 PM gussetgus Hyundai Sonata 9 02-05-2011 06:26 PM miniwangja General Tech Help 8 06-12-2009 05:49 PM DarkKinght73 Hyundai Sonata 1 12-06-2008 01:21 AM glampins Hyundai Accent 0 07-08-2008 08:18 PM 01, 2004, 2008, 2011, 24, camshaft, crank, crankshaft, hyundai, located, location, position, sensor, sonata, trigger What are the symptoms of a failed camshaft position sensor?A glowing check engine light, stalling, poor acceleration and bad fuel mileage are all possible signs your camshaft position sensor may be failing. Gone are the days of carburetors and distributors, replaced by a variety of sensors that help a car's computer get the maximum performance out of the engine.
|
2004 hyundai sonata 2.4 camshaft position sensor location
Related Posts
Copyright © 2024 hanghieugiatot Inc.
