Here is a quick instructions of how to reprogram genie garage door keypad, normally user of this device face problem whenever they forget the code and don’t know how to reprogram it before resetting the code. Because the device states on its cover to see owner’s manual for reprogramming and reset. And most of the time user don’t have manual for this task. So here are steps to follow of How to Reprogram Genie Garage Door Keypad
1- Hold Program button with Digit 6 and up/down button at a same time. 2- And then Press 3, 5, 7 and then press Program button. 3- Next step is to reset pin by pressing whatever you want the code For example press 2344 and then press Program button and wait for the red lights to blink couple of times and then it will goes off. 4- Next step is to go back to your garage door opener hit the Learn Button and you will see red light blinking below learn button. More Garage door: Smartlife Garage Door Opener After Hit the learn button you have a 30 second for verifying the code. 5- Go back to Keypad and press the new CODE 2344 and press up/down button. 6- Then go back to Garage door opener and you will see the red light blinking turn a solid red color. 7- After you confirm about the solid red color you again have a 30 seconds timeframe, so go back to Keypad and press UP/Down Button. 8- Note: Before testing your new reprogram code, you have to wait until the two backlit keypad lights turn off. You have to go through the whole process again. If you test the code before turning off the keypad back lit light. This keypad is NOT compatible with Genie of Fairview Intellicode remotes. If your keypad looks like this but has Intellicode on the cover go to the next set of programming instructions below. Step-By-Step Programming Instructions
The Door Code in step 4 above is determined by the internal code switches inside one of your remotes. Look at the first 3 switches and determine which ones are up and which are down. Look at the chart below and write down the corresponding Door Code Number. Look at the next 3 switches and determine its code number. Continue until you have 4 Door Code numbers for a 12 switch remote, or 3 Door Code numbers for a 9 switch remote. Chart ASwitch SettingsDoor Code NumberUpUpUp7UpUpDown6UpDownUp5UpDownDown4DownUpUp3DownUpDown2DownDownUp1DownDownDown0Genie Wireless Intellicode Keyless Entry Pad Programming3 Models were made for Intellicode remotes, shown here from the oldest to the newest. Model 1: Intellicode Models GWKIC, ACSDG ( black with slide-up cover and the work “Intellicode” printed on the cover. Two Part, Step-By-Step Programming. Part 1
Programming your Intellicode keypad
Part 2 Model 2: Intellicode Model GWKP
Gently press and release the radio receiver Learn Code button on the motor head in your garage to start the red indicator light next to the button will start blinking. This small black button is always found near the floppy antenna wire and is usually behind the light cover for your light bulbs. While the indicator light is blinking enter your PIN number and Press the UP/DOWN arrow button several times ( 3 or 4 ) until the door is activated. Model 3: Programming instructions for your Genie of Fairview GK-BX Wireless Intellicode Keypad.(this keypad is off-white with a flip-up cover and the PROGRAM key is above the 2 key) Gently press and release the radio receiver Learn Code button on the motor head in your garage to start the red indicator light next to the button will start blinking. This small black button is always found near the floppy antenna wire and is usually behind the light cover for your light bulbs. While the indicator light is blinking enter your PIN number and Press the SEND button several times ( 3 or 4 ) until the door is activated. To clear out the factory settings or the previous code, press and hold both the PROGRAM key and the Up/Down arrow keys until the red light on the keypad flashes twice and goes out.
Gently press and release the radio receiver Learn Code button on the motor head in your garage to start the red indicator light next to the button will start blinking. This small black button is always found near the floppy antenna wire and is usually behind the light cover for your light bulbs. While the indicator light is blinking enter your PIN number and Press the UP/DOWN arrow button several times ( 3 or 4 ) until the door is activated. Note: Once your keypad is programmed to your garage door opener, chaning your PIN to another code is easy. Just enter your present PIN and hit the PROGRAM key, then enter a new PIN and press PROGRAM. Wait for the backlight to go out and test. The keypad should now be set to the new PIN Programming your GK-BX for the newest line of Genie garage door openers. These include the Genie InelliG, TriloG, SilentMax, PwerMax, GPower, and PowerLift Series Openers (Intellicode II). These include models 4024, 3024, 4042, 3042, 4022, 3022, and 4046, 3064, 4062, 3062, 2564, 2562. Looking up at the bottom of the Genie motor head cover in your garage you will see a set of black buttons depicted in the drawing below along with two LED lights shown here in grey.
** If after performing Step 4 above and releasing the square button, the round LED comes on and stays blue, follow the instructions below: |