03 Functions TEMPO Function Use this to change the TEMPO while music is playing. 1. During playback (CD-DA/MP3/WMA), press the TEMPO button on the remote control or on the main unit. 2. Select the desired TEMPO by using the EFFECT- , + button on the remote control or VOLUME/SEARCH JOG on the main unit. | NOTES | ✎ You can set each of the TEMPO functions from -10 to +10. The initial setting for all functions is 0. ✎ TEMPO Function does not operate in the Bluetooth, TV SoundConnect, TUNER and AUX mode. ✎ When you turn TEMPO off, all TEMPO settings are lost. BOOTING SOUND Function When the Booting Sound Function is on, your Hi-Fi component demonstrates it's audio prowess as it boots up. 1. Press the product's GIGA PARTY button or the remote control's GIGA button for about 3 seconds. The BOOTING SOUND menu appears on the display panel. 2. Press the product's GIGA PARTY button or the remote control's GIGA button for about 3 seconds to turn the BOOTING SOUND. Software Update Samsung may offer updates for the product's system firmware in the future. If an update is offered, you can update the firmware by connecting a USB device with the firmware update stored on it to the USB port on your product. Note that if there are multiple update files, you must load them onto the USB device singly and use them to update the firmware one file at a time. Please visit samsung.com or contact the Samsung Call Center to receive more information about downloading updates files. • Select USB function, insert a USB device containing the firmware update into the USB port on the main unit. • Updating firmware may not work properly if audio files supported by the product are stored in the USB storage device. • Do not disconnect the power or remove the USB device while updates are being applied. The main unit will turn off automatically after completing the firmware update. • After the update, all settings are reset to their factory default settings. We recommend you write down your settings so that you can easily reset them after the update. If the firmware fails to update, we recommend formatting the USB device in FAT16/FAT32 and trying again. • Once the software update is completed, turn on the product with no disc inserted. The " NO DISC " message appears on the display. Press and hold the STOP button on the main unit for longer than 5 seconds. " INITIAL " appears on the display and the unit powers off. The upgrade is complete. • Do not format the USB device in the NTFS format. The product does not support the NTFS file system. • Depending on the manufacturer, some USB devices may not be supported. • If the firmware fails to update, most functions will become inoperable and " PLEASE UPDATE MPEG SW " will appear on the display. Update the firmware again. 27 English [MX-JS8000-ZP]AH68-02771H-00ENG.indd 27 2015-03-31 오전 9:18:16 20 English English 20 English 21 Troubleshooting Refer to the chart below when this unit does not function properly. If the problem you are Symptom Check/Remedy I cannot eject the disc. • Is the power cord plugged securely into the outlet? Playback does not start • Are you using a deformed disc or a disc with scratches on the surface? No sound. • The unit does not produce sound during fast playback and slow playback. • Are the speakers connected properly? The remote control does not • Is the remote control being operated within its operational angle and distance range? • Are the batteries drained? • The product is not working. (Example: The power goes out or • The product is not working normally. • Reset the unit: With no disc inserted and the “NO DISC” message on the display of the product, press and hold the STOP (@) button on the main unit for longer than 5 seconds. Using the RESET function will erase all stored settings. Can't receive radio broadcasts. • Is the antenna connected properly? area with good reception. How do I reset my Samsung Giga radio?1 Solution. To reset your device, press and hold the stop button (on the front panel) for more than 5 seconds.
How do I use Bluetooth on my Samsung Giga sound?Press the PAIRING button to enter the "BT PAIRING" mode. You can connect the Party Audio to a new Bluetooth device in this mode by selecting the Party Audio from the Bluetooth device's search list. Press the ADD STEREO button to connect to another Party Audio wirelessly.
|