03
Functions
TEMPO Function
Use this to change the TEMPO while music is
playing.
1.
During playback (CD-DA/MP3/WMA), press
the
TEMPO
button on the remote control or
on the main unit.
2.
Select the desired TEMPO by using the
EFFECT-
,
+
button on the remote control or
VOLUME/SEARCH JOG
on the main unit.
|
NOTES
|
✎
You can set each of the TEMPO functions from
-10 to +10. The initial setting for all functions is 0.
✎
TEMPO Function does not operate in the
Bluetooth, TV SoundConnect, TUNER and
AUX mode.
✎
When you turn TEMPO off, all TEMPO settings
are lost.
BOOTING SOUND Function
When the Booting Sound Function is on, your Hi-Fi
component demonstrates it's audio prowess as
it boots up.
1.
Press the product's
GIGA PARTY
button or
the remote control's
GIGA
button for about
3 seconds. The BOOTING SOUND menu
appears on the display panel.
2.
Press the product's
GIGA PARTY
button or
the remote control's
GIGA
button for about 3
seconds to turn the BOOTING SOUND.
Software Update
Samsung may offer updates for the product's
system firmware in the future.
If an update is offered, you can update the
firmware by connecting a USB device with the
firmware update stored on it to the USB port on
your product.
Note that if there are multiple update files, you
must load them onto the USB device singly and
use them to update the firmware one file at a time.
Please visit samsung.com or contact the
Samsung Call Center to receive more information
about downloading updates files.
•
Select USB function, insert a USB device
containing the firmware update into the USB
port on the main unit.
•
Updating firmware may not work properly if
audio files supported by the product are stored
in the USB storage device.
•
Do not disconnect the power or remove the
USB device while updates are being applied.
The main unit will turn off automatically after
completing the firmware update.
•
After the update, all settings are reset to their
factory default settings. We recommend you
write down your settings so that you can easily
reset them after the update.
If the firmware fails to update, we recommend
formatting the USB device in FAT16/FAT32 and
trying again.
•
Once the software update is completed, turn
on the product with no disc inserted. The "
NO
DISC
" message appears on the display. Press
and hold the
STOP
button on the main unit for
longer than 5 seconds. "
INITIAL
" appears on
the display and the unit powers off. The upgrade
is complete.
•
Do not format the USB device in the NTFS
format. The product does not support the NTFS
file system.
•
Depending on the manufacturer, some USB
devices may not be supported.
•
If the firmware fails to update, most functions
will become inoperable and "
PLEASE UPDATE
MPEG SW
" will appear on the display. Update
the firmware again.
27
English
[MX-JS8000-ZP]AH68-02771H-00ENG.indd
27
2015-03-31
오전 9:18:16
20
English
English
20
English
21
Troubleshooting
Refer to the chart below when this unit does not function properly. If the problem you are
experiencing is not listed below or if the instructions below do not help, turn off the unit,
disconnect the power cord, and contact the nearest authorized dealer or Samsung
Electronics Service Center.
Symptom
Check/Remedy
I cannot eject the disc.
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
Playback does not start
immediately when the
Play/Pause button is pressed.
• Are you using a deformed disc or a disc with scratches on the surface?
• Wipe the disc clean.
No sound.
• The unit does not produce sound during fast playback and slow
playback.
• Are the speakers connected properly?
• Is the disc severely damaged?
The remote control does not
work.
• Is the remote control being operated within its operational angle and
distance range?
• Are the batteries drained?
• The product is not working.
(Example: The power goes out or
the front panel key doesn't work
or you hear a strange noise.)
• The product is not working
normally.
• Reset the unit: With no disc inserted and the “NO DISC” message on
the display of the product, press and hold the
STOP (@)
button on the
main unit for longer than 5 seconds.
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
Can't receive radio broadcasts.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna in an
area with good reception.